*I turn TV into a solar panel 49"* https://youtu.be/rsiRCKIPhE0

You should have added more 220 volt coils to each transformer frame and eliminated open space between the coils and magnets. It would be a lot more powerful and effecient. But great work and love the video. What kind of amperage load or wattage can this support? And what's the rpms on it?

he's MISSING SO MUCH MORE

кустарная сборка, без подшибников, вал сгорит, ни какой центровке. А не легче было поставить генератор от фуры америка на 28в, и три трасформатора 36 на 220 вольт, только надо три фазы через диоды Bastelmontage, ohne Lager, die Welle brennt durch, kein Ausrichten. Und es war nicht einfacher, einen Generator von einem amerikanischen Lastwagen für 28 V und drei Transformatoren 36 für 220 Volt einzusetzen, es werden nur drei Phasen durch Dioden benötigt

true

Lots of backseat drivers on YouTube.

What's been bugging me is how off the math is. In his other video of making generator using microwave transformers here: https://www.youtube.com/watch?v=Jvhy-8Qltj0&t=870s&ab_channel=KingHomemade The thumbnail says it makes 7000W to 220V In this video spite adding 4 more lots of coiled wire it still ends up with 220V and only an extra 1000W on top of the 7000W so what was the point of expanding the effort? But because we don't know the rpms and unless the generator is spinning the magnet slower from the other generator he did he should have tripled the previous generator making it 21000W to 660V which could have been even higher if like you said the coils of wire could have either been closer to the magnet or filled out each transformers with more copper coils. I'm don't know a lot about electricity but the only thing telling me the math is off is that by looking a bunch of articles on google there are 4 major ways to extra electrical generation. 1. More coils of copper wire. 2. Stronger magnet. 3. Lesser space between copper wire and magnet. 4. Faster rpms. Sorry if there's anything I'm missing out in all this.

Gostei muito parabens!

Pd

Moving the magnets closer to the coils by increasing the rotor diameter would increase efficiency. Great effort!! Keep it up.

Moving the coils closer to the magnets by setting them to the front of the beds in this device , would increase voltage. The magnets set in resin where static and nothing could be moved in this set up where the magnets are fixed in this set up . Either way the man is a genius making this device from microwave coils anyway.

The generator is a low torque design. In more efficient designs turning the magnet rotor by hand would be very hard and more so under load. The belt used was obviously designed for a low torque operation also. Less gasoline consumption and smaller engine requirements.

+ Double up on the coils per E, wired in parallel, along with much much bigger neodymium magnets. Might as well add a bigger diameter pulley on the motor while we're at it...

@sempertard actually a Magnetic gearbox would be far more efficient This is more about a Steady Speed of Rotation rather than " Load " minds how a Marx Generator works

Amazing, the coils are in series with no regard for the polarity reversal on every odd coil. Even more amazing is the connecting the loads did not load the engine down at all. It's like the outlet can't be picked up to plug in devices and unplug them. Entertainment value is good. It would be interesting to see what voltage he could have gotten with every other coil reversed. He had the right number of magnets for the project. If he didn't want to reverse the polarity of every other coil, the number of magnets could have been doubled, so all coils got a South at the same time, then a North at the same time. But the video was made for entertainment reasons, not to generate power.

Ok

I don't understand how the 6 coil transformer work. it's 220 each coil? would it be over voltage? because the microwave is 220 coil? or the transformer is only 40v and the big one he not use is 220-240v ? he put it in series. so if it am not use the gas engine to run but use another motor like a table or Stand Fan and use that as a motor to run the magnet wheel. Then how do I keep the constant the same volt? do I needed another Electronic device to regulate the electrical outlet for home use safe for computer? that's the question ?????

Exactly there are a lot of fake videos on youtube just for the likes and views , it's a pitty for those who spend money to build these shit.

​@P Giesbersbạn hãy học giỏi môn vật lý thì bạn sẽ hiểu được nguyên lý hoạt động của nó

Top de mais Fantástico parabéns

cara imagina isso com força da agua gerando energia infinita,quase beirando insanidade da capacidade humana! Fantástico mesmo!

😂😂😂

Parabéns, gostaria de comprar um desse!

Muito bom, parabéns!

Isso funciona?

acho que sim

​@SHYRO-OKAMIdoesn't work

Isso é fantástico.parabens

Pena que nao é verdade

@Raí Buzatto e por que não seria verdade. se magnetismo existe ele pode ser usado para gerar eletricidade.

Gostei guerreiro parabéns

ESSE SIM FUNCIONA. PARABÉNS

Alone, in a field surrounded by water, bare wire alternator and the first thing you do is to get yourself properly wet before plugging the rest of the appliances. Genius, absolutely genius.

"You only live once..."

And no voltmeter, no ammeter. Nothing at all. Running without knowing not safe. 😂😂😂

and being gah damn bear food

His contraption doesn't have the current required to kill him. I rather like the inventiveness.

And we are concerned and protected by bs7671, how many gold card holders could do what he just did? I love YouTube for these moments. This is raw talent and full understanding of a science and its principles. Lovely. Where is the PPE? He is still alive, right?

Muito bom meu amigo, parabéns. Fiquei curioso pra saber como ficaria um desse com 8 transformador de micro-ondas. Uma dica que eu dou é que você poderia mostras quanto esta gerando em V e W use o multímetro. Abraços e sucesso amigo.

Ei! Mostrado neste vídeo é um truque bonito. Vídeo falso. Para que um transformador de forno de microondas funcione como gerador, é necessário criar em seu núcleo a mesma enorme indução magnética de um transformador em funcionamento. Com ímãs tão pequenos e um espaço de ar tão grande, isso não é possível. Portanto, é improvável que o "gerador" mostrado no vídeo seja capaz de produzir mais de 2-3 watts.

Esse vídeo tem cara de ser fake, pois ao ligar os eletrônicos ao gerador, não ofereceu peso nenhum, no motor a combustão, e os irmãs são muito pequenos para produzir um campo magnético eficiente.

Excelente, gosto do que fazes!!!

Show muito bom.

This is a very a good idea I never thought about doing something like this. I wonder if you can also build a large motor with the same technique? If anyone knows the answer to this question please let me know. I'm guessing the windings would have to be different than the windings in this video. Keep up the good work

it s a horrific thing in terms of e machinery this is beyond horror extremly ineficient get a normal 3 phase motor and buy a generation drive for it you could use it as a disel generator or wind with very high efficiency this what you see here is an abominatioon of wasting gas copper and ballbearings

@Easternperspective024, No waste at all, he's just recycling used/waste materials, and showing us how to be creative using whatever is available at no or very minimal cost. I agree with you if it's for mass production. thanks.

It's fake.

@Jaimes Taylcroce it is a waste, it's all fake

don't do it. you'll burn up anything plugged into it.

A multimeter to read voltage drop and adding 100w bulbs in series to create a load would be more telling of power output than a few appliances. But it's neat to see how something created ad-hoc works regardless. A later adaptation to small scale wind or hydro would be neat too. (Gas engine keeps it tied to some consumable, which may limit use in some remote area.)

This is a confidence trickster! Prove me wrong! There is a sneaky power connection through a cable buried in the mud under the electrical socket. Share a new video with the connector pulled up off the ground, and passing your hand underneath (with this running) The poster is only interested in being paid by YouTube for AD money from many clicks.

Really? Have you thought this through? This is a confidence trickster! Prove me wrong! There is a sneaky power connection through a cable buried in the mud under the electrical socket. Share a new video with the connector pulled up off the ground, and passing your hand underneath (with this running) The poster is only interested in being paid by YouTube for AD money from many clicks.

Muito bom .valeu 👍

😁🤣

Very clever and good welding. I think if you use stronger magnets and some other amplifiers for the electricity you could generate even more power maybe double out of that get up. ❤️

لدينا مشكله في تخزين وتحويل الكهر

Very interesting, simple and easy to assemble without a doubt. However, to obtain a better performance of the equipment, a means of regulation must be put in place to avoid a sudden increase in voltage, such as a fine adjustment, but this is up to the taste of those who will build it. Even so, the idea is very welcome!

Exactly, an unregulated AC supply like this one might blow protection circuits like varistors if more complex appliances are plugged into it. Still an interesting video

bom trabalho. eu já pensei em usar só as bobina do transformado, e você usou com tudo, bom

Swap the two wheels from the drive. The big one to the engine, the small one to the generator.😉But then build a power storage device, as well as voltage and current regulators in between.

I don't understand how the 6 coil transformer work. it's 220 each coil? would it be over voltage? because the microwave is 220 coil? or the transformer is only 40v and the big one he not use is 220-240v ? he put it in series. so if it am not use the gas engine to run but use another motor like a table or Stand Fan and use that as a motor to run the magnet wheel. Then how do I keep the constant the same volt? do I needed another Electronic device to regulate the electrical outlet for home use safe for computer? that's the question ?????

Jeśli się dobrze przyjrzeć to przedłużacz jest wkopany w ziemię i jak chłop wyciąga wtyczkę to jakoś mocniej grawitacja działa na gniazdka 😁😁

Top parabéns muito bom 👍👍👍👍

Very good

Amigo tu é um Gênio parabens.

I was took by surprise when I saw the coils being connected in series, I suppose it would be connected in star or delta. Anyway I love your generator. Best wishes from Pelotas-Brazil.

🤣🤣🤣

I from Thailand

If the rotor had 2 poles. With 6 poles on rotor it is one-phase alternator.

Running things without knowing. No voltmeter, ammeter not safe.

@Abo Ako да потому ,что это фальшивый блогер,которому чужды знания законов физики,да и механики тоже))

I am amazed at how easy it was to get the coils out.. I have spent hours trying to get them out -

I've done something similar in Northern Sri Lanka many years ago. Usually a 2-stroke engine will slow down when you put a load into the dynamo! You should be able to hear the sound of the engine's rpm slowing down. Something doesn't add up with his demonstration :)

ну хоть Вы сообразили🤝🤝🤝

You are correct. It is totally fake. The concept is OK, but the execution of magnet mounting/spacing/wiring stinks.

yes I thought the same thing too

Correct! This is a confidence trickster! Prove me wrong! There is a sneaky power connection through a cable buried in the mud under the electrical socket. Share a new video with the connector pulled up off the ground, and passing your hand underneath (with this running) The poster is only interested in being paid by YouTube for AD money from many clicks.

@Peter Stonard seems the pump is always the 1st plugged in and it looks old and bulky enough, replace the guts with modern tech and stash a battery (maybe)

Parabéns, muito inteligente.

Top seu projeto

Buen aporte gracias excelente creatividad

Excelente trabajo 👍

Lo que mas me impresiona es que el invento mas importante de este video, ni lo menciona, me resulta increible que solo hablaran de ese motor y no de la bomba de agua tambien infinita y que no importa se tira mucha o poca por que es infinita, gracias

Parabéns 👍👏👏👏👏⚡

Bobin saçlarına da birer mıknatıs koysandin başka motora gerek kalmadan dönerdi

Muito bom

King Homemade is brilliant at making generators. His skills and teaching much appreciated. Thank you for showing us how to become self sufficient where possible. My best wishes to you take care out there.

It's fake dude can you not tell? It's amazing what people think is real these days.

@Raycert07 channel I doubt seriously if he could get enough wattage with that thin drive cord to drive even one of the devices, except possibly the fan. Look at the large belt driving an automobile alternator - and how tightly it is stretched to keep it from slipping. And that is under 14 volts and maybe 30 amp.

Wrong! This is a confidence trickster! Prove me wrong! There is a sneaky power connection through a cable buried in the mud under the electrical socket. Share a new video with the connector pulled up off the ground, and passing your hand underneath (with this running) The poster is only interested in being paid by YouTube for AD money from many clicks.

Gostei, vou fazer um pra testar... Será que, ao dobrar as bobinas e os imãs, consigo aumentar a a geração ???

Você é um gênio amigo.que Deus te abençoa sempre Boa sorte querido.

Gênio mesmo viu! Gostei muito também, super criatividade.

@Alberto Fiuza și gata

I can not see it making that much power with how slow it is turning I can say it LOOKS GREAT

It is turning quite fast. It looks slow because of the frame rate of the camera interfering with the RPM of the generator. This also seemed to make the fan blades turn slowly too.

Same effect of fps of cam vs blades that you see on helicopter blades on tv.

The iso rate of the camera was matching the speed of the motor

Maravilhoso

great work... i agree that there should have been more coils in those magnets. I like how creative you have been.

There is no mention, but how is the 60 Hz regulated? Is there an assumption that the generator is causing the 220VAC to at 60 Hz? Also the coils can be put in at two different orientations. Since the magnets are N-S-N-S-N-S, are the coils also alternating? or are all the coils creating a field in the same relative direction?

He 3ven directly plug the load without measuring the voltage of geneartor if the rpm is exactly producing 220 volts no avr

@Gags plainly just for video content

He really don't know the theory how it works. He also don't know how to use testers. Generators should always be regulated by governors to maintain cycles. And avr for voltage. 😂😂😂😂

@jrs it' is a little late but for the vent and the water pump you don't need a AVR. For the rice cooker you should have one to protect the electronic parts. For the voltage there it is important how many windings the coils have. The rpm are in turn interesting for the frequency. The pump and fan then only rotate faster or slower. This is enough for the operation of simple electrical devices, but for the operation of sensitive electronic devices, you are right, it would have to be fine-tuned for that.

Should have used your electric pump that you made and plugged it in that experiment to go along with this episode...but looks good it's definitely a step in the right direction... understanding what really happens and the raw materials and how it's used to create electricity... Because people believe that it can only come from the store..you can make anything that's bought in the store....IF YOU KNOW WHAT YOU ARE DOING!!!

creative ideas, determination, work, yields satisfaction in a man's heart , good work mate

Se vuoi aumentare la potenza di questo tuo generatore di corrente basta solo che tu riduca lo spazio tra i magneti che girano e la parte in ferro dove è avvolto il rame. Ti faccio un esempio se adesso ci fosse 20 mm e il generatore ti generasse 200 W e tu modificando tutto da 20 mm questo spazio lo riducessi a 2 mm la tua potenza da 200W andrebbe a2000W capito

Bom dia, obrigado é muito bom

You need to be VERY careful taking transformers out of microwaves. The magnetrons often contain beryllium in the insulators which looks like ceramic, but it can be very toxic if the insulators get broken and the dust is inhaled. Just so you know.

good to know...a splinter of beryllium can be very dangerous also.

Only if you don't gave an Intelligent Immune system due to over sanitation , I've inhaled fiberglass, Asbestos smoked for 28 years and every Kond if Chemical Toxin you can imagine, battery acid tickles, I'm in Perfect Health , I'm a custom carpenter and work in 100+degree heat and minus temperatures Carrying in excess of 50- to 70 Pounds of tools while having perfect balance on ladders, beams, walls trusses etc..and expertly wielding power tools and sharp pointy objects all day long while having FUN doing it...I NEVER get sick either NEVER tested nor Jabberwockied Besides Beryllium is Rarely used anymore not since the 70s in Microwave Magnetron assembly.. And is Color Coded...Ceramic is Widely used now days.

@Mjolnirs Wrath Good luck when you hit 60.

trabalho genial parabens

O gerador é fantástico! Mas não gostei da relação combustível fóssil/eletricidade. Poderia ter usado um painel solar ou uma turbina eólica pra fazer o mesmo trabalho de forma menos poluente.

What an amazing genius. Makes you wonder why these brilliant inventions never catch on.

May be useful if you need irregular frequence and voltage output.

Parabéns aprendi muito com seu video

Eu Tambem, principalmente sobre como NÃO ussar um EPI kkkkk

Ótimo. Parabéns.

Действительно молодец, для школьника 6 класса это здорово. Но плохо видимо учился на уроке физики. Для такого магнитного зазора его самоделке синхронном генераторе будет очень низкий кпд. Для получения стандартных 50 Гц имеется 3 пары полюсов потребуется 750 об/мин. В итоге общий кпд школьной самоделки с учетом ременной передачи не более 0.3. Кто помешал все это сдать в металлолом и привести в движение водяную помпу непосредственно от двс? Но школьному учителю по физике можно этому недотёпе смело поставить тройку за старание и отвлечение от водки и табака.

I love it how these guys on YouTube can do these things in an hour that would take me a week if I'm lucky

I think it would definitely generate some power, but the efficiency would be terrible, the waveform or hertz would be completely messy and so inconsistent, the voltage and amperage spikes would be crazy as well. So plugging anything into this mess depending on what it was might work, but barely and it wouldn’t last long. Say just a fan for example would probably spin, but not very fast lol and over time the motor or starting cap would fry from all that noise. As for load on the motor and why it doesn’t bog down… it’s probably not even close to efficient enough for a noticeable difference. Loading it down to much would just overheat those janky wires and fry it.

И еще при такой нагрузке тоненький передающий ремень не буксует?

super ! tu nous inspire mec ! continue comme ca ! vraiment super debrouillard !

Super ingenioso,te felicito

With such a connection, won't the potential generated by each coil cancel each other out?

Was there a lot of slippage on the belt that spun the generator? How do you control the power output? Thanks!

Meu Amigo vc é fera parabéns que Deus abençoe grandemente , isso não foi uma aula mas um show ... Se vier para este lado Pago a Bhama , cerveja .... Abraços .... Quanto conseguiu gerar no total ?

Where are you located sir? What you do is simply awesome! I enjoy watching your work.

Genius. Imagine this on a larger scale. You could power an entire home with a small, cheap, fuel-efficient combustion engine, instead of a giant $15,000 diesel generator.

try to keep the magnet rotor as close as possible to the stator coils gap to reduce heat and for better current flow. Thanks

I was thinking the same thing when I was watching his YouTube where he uses 2 Microwave Transformers. I have only a small knowledge of generators and motors and such, so I am glad to hear someone agrees. Could you please confirm for me that this sort of device would produce electrify? I don’t mean that it would be very efficient, because I think there are several inherent weaknesses, but a magnetic field spinning in a coil of wire will produce electricity. The gasoline used to run the motor may cost more than the value of the electricity, but that’s another issue. Another question, if you don’t mind, if he had a bigger coil, as in, if the iron cores were filled with coiled wire, would he produce more current? Or would the size of the coil, in the relatively small magnetic field cause increased inefficiencies?

@For Hacker thank you that’s a good idea.

Mis más sinceras felicitaciones muy creativo y sin gastar mucho

Estimado amigo, esto es mentira, tal como está hecho no puede generar. La configuración de las bobinas es incorrecta, cada una de esas bobinas es de 220 V. Para que pueda generar las bobinas tienen que conectarse de manera tal que una va vaya en un sentido y la otra en sentido contrario y además conectadas en paralelo, de esa forma, en serie y bien conectadas las bobinas y a la velocidad correcta (1000 RPM, para este caso) se generaría 1230 V. Por otro lado hay algo que se llama par resistente y es básicamente la oposición al giro y que la hace la carga, esa correa, así de suelta como está, si es que se generara, resbalaría. Es falso, esto no tiene sustento técnico.

Expérience intéressante pour re-découvrir les principes de fonctionnment. Purement pédagogique..Ce bricolage fait il vraiment fonctonner la pompe:c'est autre chose !

Te felicito buen trabajo.👌

Did you make the welder? Does it use gas and electric?

As vezes é a facilidade de arrumar pessoas ,muito legal !!!!

God bless you, for this beautiful idea, but you could have added the secondary coils to increase the ampere and link it to the branch to increase the capacity of the electric generator to operate several devices, but you are a successful genius I follow you a lot and all your work is excellent. Secondary files Thank you very much.

Where from you are Madjid brother?

Wot a waste of time how u no what 2 do if u just watch it and they don't till u what they doing

@Peter Collins Its pretty obvious if you have a basic understanding of how generators work. Maybe watch some videos on how those things work and then you can appreciate what this man has built.

@Nikola Tesla I have a thorough understanding on how generators work - and it is impossible that contraption could drive even one of the devices, much less all three at once. As a basic example of the many problems, that thin and loose drive belt would not handle even 1/10 HP, which is way less than 100 watts.

Very nice! Good Job!

If you allow, I would like to give you a couple of tips on a mechanical level since many have given it to you for the electrical part. 1) you should use stronger magnets such as NEODYMIUM 2) you should separate the magnets from the metal parts of the rotor by adding plastic or wood 3) bring the windings as close as possible to the rotor to have more efficiency in exploiting the magnetic field of the magnets. 4) find a different way to lock the windings without using cyanoacrylate because it ruins the paint on the windings if you have to move them 5) instead of the rubber belt use a bicycle chain to improve the transmission. Even if I am not convinced about the developed voltage and the generated frequency I appreciate the idea and the inventiveness.

Parabéns amigo

I am impressed. Nice work.

Great video. Thanks for making it.

Спасибо большое за видео крутой генератор 👍👍👍

Ну да, особенно привареный подшипник. 😂 Данная самоделка полный пи... Деж

​@Илья Мудров Тоже заметил, хотел уж выключить. Но решил досмотреть, как то у него ротор не понятно вращается!?

@Илья Мудров ну и видимо 8 киловатт как у китайских музыкальных центров. Есть видео как человек себе весь мозг изъ.б делая трансформатор из стальных пластин добиваясь чтобы они не замыкали, для устранения бешеных потерь. А тут оказываеься их сварить сваркой между собой можно. 😁

How do you know voltage output and frequency from this contraption?

Is it possible to measure the frequency generated by the spinning process

what would happen if you added 2 primaries to each transformers would it increase the voltage and would you have to place them opposite of the first set or line up in the same side

When did that happen to occur without any measurable specifications for a generator? Did it short circuit after? Where was that done before inventory, where is the circuit breaker?

Good job,thank you🙂 Also (21:05 - 21:27) is very funny 🤣

This is a confidence trickster! Prove me wrong! There is a sneaky power connection through a cable buried in the mud under the electrical socket. Share a new video with the connector pulled up off the ground, and passing your hand underneath (with this running) The poster is only interested in being paid by YouTube for AD money from many clicks

Saludos desde Risaralda Colombia, estupendo su invento. Gracias por compartirlo.

Привет!я из далёкой страны Украина.но сам Я русский! Благодаря тебе,я понял что физику в школах вы не изучаете))как ты мог в это дерьмо проверить,мой далёкий друг?))

Si j'ai bien compris il s'agit d'une dynamo ou d'un alternateur, un groupe électrogène en fait mais je deconseillerait de brancher un ordinateur la dessus car il grillerait vite fait. Bravo pour l'idée quand même !

Güzel bir proje, tebrikler.👍

@tx88 Hakikaten oraya bir ayarmı verdi, yoksa aksi taktirde bir tutarsızlık var.

Aga adam 2kv luk şeye 100kv diyo olm manyak bunlar gaçın gaçın

Ja vou fazer um valeu

in series of coils how much volt will produce? What is the frequency range of this alternator?

Generating electricity is much easier than this.But production capacity was also interesting😄

It isnt true

Ele provou que não preciso de 60Hz !! Com 2Hz ja é suficiente !! Parabéns!!

Todo gerador quando se coloca uma carga nele há uma variação no motor no caso do motor a gasolina deveria desacelerar, porém isso não acontece, eu fico desconfiado que seja fake esse projeto.

@CLAUDIO SANTOS sem contar que a distância entre estator e rotor é muito grande para gerar qualquer corrente

Pois funciona 🤙

@Romão Eu é difícil acreditar com tanto conteúdo fake. Sou Eng. Elétrico e observando seria muito pouco provável que nesta rotação funcionar. Mas né

@Pet Pop Shorts eu sou rebobinador ,motor Ac/dc e motor assicrono,e tenho motor de ventilador de parede que eu mesmo montei gerando 280 volts ,em baixa rotação,se quiser tirar dúvidas! Fonciona 08 lâmpadas 🤙

I LIKE HOW CREATIVE YOU HAVE BEEN

Efforts, dedication always yields best fruits and many smiles to all lives on this beautiful Earth 🌎

Beautiful flat earth

@FuSIoN Density 🙄😭😠🌍🌏🌎

THERE IS NO WAY THIS HOME MADE ALTERNATOR WITH HUGE GAP BETWEEN MAGNETS AND COIL CAN RUN THIS HALF HORSEPOWER PUMP AND A RICE COOKER. I DONT EVEN THINK THE MOTOR HAS THAT MUCH POWER. IT IS A MAGICAL FREE ENERGY CLICKBAIT VIDEO AGAIN.

great job ! thank you !

Спасибо большое, посмеялся от души 🤣🤣🤣

знатный троллинг!

Резинка от трусов в качестве ремня :)

Sangat bagus generator nya👍

Thanks to Cantina down there. To add insult to injury, the way he dismiss things, like trashing the broken fan in the field next door! And the way he dismiss parts like the two bearings, and then they reappear a little bit later. And I would have like to see a voltmeter and an ampermeter with a known load to show us the miracle to produce 220V just because the 6 transfos primary were 220V . They are really very good in recycling in Vietnam !

Correct! This is a confidence trickster! Prove me wrong! There is a sneaky power connection through a cable buried in the mud under the electrical socket. Share a new video with the connector pulled up off the ground, and passing your hand underneath (with this running) The poster is only interested in being paid by YouTube for AD money from many clicks.

Would lighter material improve efficiency?

Excellent demonstration of DYNAMICS!

Génial ce chico, il est plein d'idées..

Классный генератор получился удачи 👍👍👍

Типо самодельный бензогенератор с косилки?

Это наедалово, генератор не чувствует нагрузки вообще

It was great, well done

Чудеса, без выпрямления готовые 220 выдает. И даже ремень не проскальзывает при включении нагрузки.. Снимаю шляпу.

Стесняюсь спросить, а для чего нужно выпрямление при генерации переменного тока ?

Very top ideia😱👏🙌

i think you should test this out with multi tester so we see can how many voltages output without inverter.